[pusako]

Guys, Will the Konig dealers be able to source these wheels??

They look good!!

tiremedia.com :: Wheel Konig - heatsink

[amulu10]

Originally Posted by torqueyTND

Nikhil ,

FYi.....When i enquired for SSW spider for 15 inch profile which is the only
avail in 98 PCD it was randomly quoted @ rs 4500/- each

let me know if this model s093 with spider black and red lip is available for 4500/- . I love this design!

[pusako]

Has anyone confirmed that the GP has 98 PCD?? because according to this link in the Fiat forum, it says its only 100PCD!!

pcd and cener hole (bore) - The FIAT Forum

[SumitBahl]

Its definitely 98pcd. Everyone installing aftermarket 100pcd alloys are using different nuts.

[amulu10]

Originally Posted by SumitBahl

Its definitely 98pcd. Everyone installing aftermarket 100pcd alloys are using different nuts.

actually no one is sure about it! no where does fiat india mention that its 98pcd . The 100 pcd alloys were difficult to fit in a PALIO and the older fiats , but the people who have fitted 100 PCD alloys in the GP say that it goes in very easily without any trouble, which makes me to think whether Punto is 98 or 100 pcd . Infact a friend who owned a fiat sienna and owns a Punto now(with 100 pcd wheels) said that it was very easy to fit that 100 pcd wheels in the Punto unlike his older sienna!

could anyone confirm that its 98pcd.?

[~~VinZ~~]

Originally Posted by amulu10

actually no one is sure about it! no where does fiat india mention that its 98pcd . The 100 pcd alloys were difficult to fit in a PALIO and the older fiats , but the people who have fitted 100 PCD alloys in the GP say that it goes in very easily without any trouble, which makes me to think whether Punto is 98 or 100 pcd . Infact a friend who owned a fiat sienna and owns a Punto now(with 100 pcd wheels) said that it was very easy to fit that 100 pcd wheels in the Punto unlike his older sienna!

could anyone confirm that its 98pcd.?

Good point.

I did a small research about this online, even thot there is no official site where it is mentioned that the punto has 100 PCD but in most forums some people have confirmed that punto has 4x100.

All fiats have 98PCDs where in punto is an exception to have 100 PCD. Do not go for my words these are just some information i found online in different fiat forums (Uk, singapore... etc)

Singapore No. 1 Car Forum & Car Club - MyCarForum > Rim PCD for different car makes..contribute!

According to Antera Grande Punto Type 199 PCD 4/100 centre bore 56.5mm bolts M12X1.25

http://www.konig.fi/fio/AnteraPDF/07/FIAT.pdf

Is there someone who can get this confirmed from FIAT?

[ms001]

its not very difficult to find out the PCD as mentioned here

WHEELS. PCD, offset, and centre spigot diameter

we can give it a try but reading using a vernier caliper, would be accurate.
May be Nikhil can help us with this one.

[~~VinZ~~]

Originally Posted by ms001

its not very difficult to find out the PCD as mentioned here

WHEELS. PCD, offset, and centre spigot diameter

we can give it a try but reading using a vernier caliper, would be accurate.
May be Nikhil can help us with this one.

Yes,

I was going through articles to find out the PCD of wheels and it is doable if someone can get the accurate reading.

eBay.co.uk Guides - Trailer and caravan wheels how to find the PCD.

[amulu10]

Originally Posted by ms001

its not very difficult to find out the PCD as mentioned here

WHEELS. PCD, offset, and centre spigot diameter

we can give it a try but reading using a vernier caliper, would be accurate.
May be Nikhil can help us with this one.

ok then time to flick a vernier from the college lab !
but problem is 100mm and 98mm are very close so there might be some error unless we use a digital vernier, infact tbhpian vigneshram was the one who raised this doubt after he fitted 100pcd plati wheels in his punto , and according to him it was very easy( similar to fitting in 100pcd car) compared to a palio . We did think about measuring it in our college but since its only a 2mm difference , wont be that easy .

[Nikhilb2008]

Originally Posted by amulu10

Nikhilb2008 do u have these with you? or can u import them on request ?

Stamford Sport Wheels

@sumitbahl i think this is what u are looking for.?

Well, it is available in India on order. It isnt too hard to get.

[SumitBahl]

Any news/updates about the confusion in PCD of Punto wheels?

[torqueyTND]

Well Guys ,

The update is ...on 19th of this month the massive shipment from Bangkok
is going to arrive at the Mumbai HQ and routed to other respective dealers across
SSW chain. ( a ssw dealer just confirmed this with me )

I think EVO is another TAIWAN make for its 98 pcd on 15 ' profile but the
choices are still dim


I think i am going to play the waiting game with these ones (SSW)
or just pretending to
blinded by the 98 pcd magic word **duh**


Attaching a pic of a Model called QUEST

[Wind splitter]

2nd Gen Punto's have 98 PCD, found this table on the internet. Not sure about 3rd Gen Punto and I belive Indian Punto is 3rd Gen.

Source: Alloy wheel fitment guide and pcd's.

[Wind splitter]

PCD table attachment.

[amulu10]

Originally Posted by Wind splitter

PCD table attachment.

but the link says that its from the year 94-00, and link for the current model.? and i pretty sure the current punto is 100pcd in Europe