[supremeBaleno]

Originally Posted by supremeBaleno

Though one baffling thing is the part 6 (VSS) is not shown inside the Speedometer Assembly.

While parts 1 to 5 are indicated in the Speedometer Assembly, parts 6 & 7 are not. Which is strange.


Also the parts table (below) is kind of confusing. Line-4 says parts 1-6 are for VXi AT (our model),
but then Line-10 says part6 is for Non-ABS model (ours has ABS). Both are contradictory.
Wondering if this is some error in the parts manual ?

[govigov]

I was not aware that you can buy Maruti Suzuki Genuine Accessories at marutisuzuki.com.

Here is a link - https://www.marutisuzuki.com/genuine...re-accessories

I found some products listed here that are hard to come by and are not listed in boodmo.

[viXit]

Hi!

Can you help me with any floor mat hooks like these from MGP which I can use in my car, we only have generic Universal foot mats in our car and hence have them sliding around all the time. Thanks in no small part to the laminated flooring of the car, which is smooth and helps the mats slide

Any and every help is appreciated, thanks

[stallmaster]

Hi Leoshashi, do you know if earlier generation Suzuki engines of F & G series are interference engines or not? I wanna know if my engines are gonna commit suicide if a timing belt worth 500 fails.

[batish]

Can anybody tell me what would be the length of the jump start cables in this accessory: 990J0M999X0-010. Tried googling but could not find any length specifications. Don't want to end up with a 2ft. cable.

[tanwaramit]

I need window side beadings for M800 AC 2010 model.

Missing for the front left door. Still in place for back left door.

Can you please help with the part numbers? I tried checking online, but got more confused.

[balenoed_]

Originally Posted by Leoshashi

Thanks for updating.

Dear Shashi, Not seeing you in action on this thread since April 6th. I hope you and your family are safe and doing good.

(Mods, off-topic, but just thought of checking in on the hero of this thread)

[Leoshashi]

Apologies everyone for the delayed reply. Was unwell so couldn't reply.

Originally Posted by revvharder

Hi Shashi sir,

Could you help me with the part number and cost of CNG filter for the 2021 Wagonr and sometime back you had recommended some door protector from MGA but I'm unable to locate that post, if possible could you share the part number for those as well.

Thanks

There are two options:

1. Replace the entire filter assembly:

Part Number: 15410M67L70
Name: FILTER COMP CNG
MRP ₹1,070

2. Rebuild the filter:

Part Number: 15414M60MA0
REPAIR KIT, FILTER
MRP ₹875

I'm not sure which door guards you are mentioning. Is it this one: 990J0M67LPA-010/990J0M67LPA-020. I have the same ones on my cars. Very discreet but does the job well if located strategically. There are many options so I'm not sure which one I had recommended in past.

Originally Posted by wanderernomad

Dear Shashi, can you please help me in locating the part number of the following alloy wheel cap and also if someone can point me out to some local source. Thanks.
Its a 2007 Baleno VXI.

There you go: Link (The love of my life - A 2000 Maruti 800 DX 5-Speed. EDIT: Gets export model features on Pg 27)

Originally Posted by Sanidhya mukund

Asking for a friend: Can the ZXI plus smart play infotainment system be fitted in an Ertiga VXI automatic? If yes, will it involve wire splicing? Also, how much is it likely to cost? He needs an automatic and finds the VXI to be quite VFM, but he needs apple CarPlay and android auto.

No idea buddy. But that system costs around 40k IIRC, and you can get much better HUs for fraction of that cost.

Originally Posted by viXit

Hi!

Can you help me with any floor mat hooks like these from MGP which I can use in my car, we only have generic Universal foot mats in our car and hence have them sliding around all the time. Thanks in no small part to the laminated flooring of the car, which is smooth and helps the mats slide

Any and every help is appreciated, thanks

You get these hooks with MGA Floor mats. Refer to the 4th point of the post: Link

Originally Posted by stallmaster

Hi Leoshashi, do you know if earlier generation Suzuki engines of F & G series are interference engines or not? I wanna know if my engines are gonna commit suicide if a timing belt worth 500 fails.

The older ones like F8B were non interference types. F8D was interference type. Which engine are you specifically asking for?

Originally Posted by batish

Can anybody tell me what would be the length of the jump start cables in this accessory: 990J0M999X0-010. Tried googling but could not find any length specifications. Don't want to end up with a 2ft. cable.

Should be around 5-6ft. I have them and will confirm the length by EOD.

Originally Posted by tanwaramit

I need window side beadings for M800 AC 2010 model.

Missing for the front left door. Still in place for back left door.

I'm posting the part numbers for all 4 sides:


Front RH: 83810M84110
Front LH: 83820M84110
Rear RH: 83830M84110
Rear LH: 83840M84110

Originally Posted by balenoed_

Dear Shashi, Not seeing you in action on this thread since April 6th. I hope you and your family are safe and doing good.

(Mods, off-topic, but just thought of checking in on the hero of this thread)

Apologies, we were all down with Covid. Posting on this thread needs a lot of commitment and effort so I was avoiding it for the time being.

Regards,
Shashi

[wanderernomad]

Thank you Shashi. Hope everyone has recovered. Unprecedented and difficult times. Please take care.

[PSM_360]

Hi,

I hope this thread is suitable for my query as it is related to the MGP part that I just received from Boodmo.

I ordered a lockset for my Maruti 1000.
Part No. 37109M70C10 ( https://boodmo.com/catalog/part-lock_set-6788349/ )
I followed the OEM parts catalogue on Boodmo.

Prior to fitting, I checked sockets on the lock cylinder and found that the new one has only one big socket but the factory fitted has two, one standard big one and a two-wire small one. Does anyone know what this 2-wire small socket is for? Although I have tried plugging in the socket, it cranks and works fine.

Please have a look at the below photos and guide.













Thanks,
PSM_360

[PSM_360]

Hi,

I need clutch plates set and release bearing for my Maruti 1000. Please provide part numbers. Esteem clutch set does not fit a Maruti 1000.

[pdpyen]

Originally Posted by PSM_360

Hi,

I need clutch plates set and release bearing for my Maruti 1000. Please provide part numbers. Esteem clutch set does not fit a Maruti 1000.

Hello sir. Please provide year of your vehicle and variant. I will try to help further.
Thanks.

[PSM_360]

Originally Posted by pdpyen

Hello sir. Please provide year of your vehicle and variant. I will try to help further.
Thanks.

1994 Maruti 1000
Chassis code: MA3EBD21S00______
Engine code: F10AIN________

[pdpyen]

Originally Posted by PSM_360

1994 Maruti 1000
Chassis code: MA3EBD21S00______
Engine code: F10AIN________

May i know if you checked this?

Clutch https://boodmo.com/catalog/part-clut...plate-5506510/


https://boodmo.com/catalog/part-22400m63b22-36616536/


I'm unable to find the release bearing. Please give some time I'll revert.


Update - This should match, confirmed with my spare dealer.

https://boodmo.com/catalog/part-releaser-5396326/

https://boodmo.com/catalog/part-bearing-5396327/


Please satisfy before ordering.

[Leoshashi]

Originally Posted by PSM_360

Prior to fitting, I checked sockets on the lock cylinder and found that the new one has only one big socket but the factory fitted has two, one standard big one and a two-wire small one. Does anyone know what this 2-wire small socket is for? Although I have tried plugging in the socket, it cranks and works fine.

No idea buddy, will have to check wiring diagram for this.

Originally Posted by PSM_360

Hi,

I need clutch plates set and release bearing for my Maruti 1000. Please provide part numbers. Esteem clutch set does not fit a Maruti 1000.

For M1000,

Pressure Plate: 22100M80031
Clutch Plate: 22400M63B20
Release Bearing: 23265-65G00

Regards,
Shashi