Radiator Fins Bent - any solution?

Raccoon · 22nd March 2012, 02:22

Car (Esteem) has been at the MASS for Body Shop work. When I'd been there to have a look, they had removed the front bumper and headlights and the radiator was in full view. Thats when I noticed that fins in the lower right corner were bent. The area of bent fins must be v approximately 25% of the total surface area. I should have taken pics, but it did not occur to me at that time.

I recall reading in books that bent fins can be straightened by some kind of tool. Today, the car went to the Workshop, after the body shop work and I asked the SA about it. He was totally blank about the issue and could offer no solution. I persisted and told him there should be some way or some tool or "comb" for the job. I even made him call his boss and ask. Spoke to the boss myself. He didn't plead ignorance outright; rather asked me to take the car to a "radiator specialis"! I didn't even know till then that there are radiator specialists. I said its unfortunate that I have to take the car to some questionable non-authorized place when I'v come to the larges MASS in the city. He said no procedure or tools for the same have been authorized for the same by Maruti, so they would be unable to help.

My questions are:

1) how good an idea would be to leave the fins as they are? They will obviously mar the cooling efficiency, but how serious would it be? The SA blankly said it should be ok to leave it as it is.

2) Does anybody know how one can get them straightened? Is there any workshop or something in Pune where I can get this done?

Not sure if I'm keen on leaving it as it is as I'd not like to keep stuff thats not working optimally.

Can somebody advice, please?

mayankjha1806 · 22nd March 2012, 04:35

Whenever the Service engineers do some sort of work around the radiator area the fins do get touched, and because they are very fragile a slight pressure is enough for them to bend slightly. When my baleno met with an accident 3 years back at MASS they had to take the radiator out to fix it, and i also noticed the fins were bend.

The function of fins is to precipitate heat and help in cooling. Now if most of the fins are alright and you have not noticed any drop in cooling effectiveness then its alright to leave them as it is, otherwise its better to show it to the radiator guys.

In my case nothing was done as it was bend on about 10%-20% of area.

condor · 22nd March 2012, 05:44

@Racoon, like Mayank said, the fins are delicate and very often get bent. But it does not mar the cooling efficiency. Any in-efficiency in the cooling may be more because of clogging inside the radiator, and hardly due to bent fins.

Unless the radiator itself is damaged, I suggest you let it be. You can also check any other car of similar age - any make any model - and you will see there are many more such cars, and running fine.

nitrous · 22nd March 2012, 06:06

Watch the temperature gauge and drive. If you feel the car's overheating, then look into the issue.
Don't try to mend what's not broken.

1self · 22nd March 2012, 06:59

One way to 'straighten' the fins (which are not badly mutilated to begin with) would be to use a strong & sturdy hair comb, the tooth spacing of which closely matches the fin spacing of your heat exchanger. Then just go over fins. They will straighten out!

condor · 22nd March 2012, 07:08

Quote:

Originally Posted by 1self

Then just go over fins. They will straighten out!

But remember - the fins are quite soft, and will bend even with when rubbed with a finger (without much pressure).

mayankjha1806 · 22nd March 2012, 08:12

Although i have never tried this myself, but my guess is combs wont work. You might end up damaging it more then what it already is.

@1self Have you personally tried this, or have you seen someone doing something like this?

@Raccoon if you are really hell bent on getting them straightened my guess is, taking a small forceps and gently straightening each millimeter of each Finn all the way might only work. A full day affair i must say with no tangible benefits. So better leave it as it is.

greenhorn · 22nd March 2012, 08:32

is it something like what happened here (scroll down for the pics) ?
http://www.team-bhp.com/forum/techni...ler-query.html

S5157 · 22nd March 2012, 08:32

The fins are bent on my 2010 sx4 as well. It is on lower side and behind the bumper slits. It looks like some flying debris from the road has caused it. I checked the same with the SA at MASS and he mentioned that it will not affect the performance and let it be like that.

1self · 22nd March 2012, 08:33

Quote:

Originally Posted by mayankjha1806

@1self Have you personally tried this, or have you seen someone doing something like this?

Yup, on my Sonata. The A/C condensor fins were quite badly bent. Quite a patient & painstaking job. Got this tip from radiator repairers. They have the same type of comb, only fabricated from metal.

ariesonu · 22nd March 2012, 10:53

Quote:

Originally Posted by Raccoon

Car (Esteem) I even made him call his boss and ask. Spoke to the boss myself. He didn't plead ignorance outright; rather asked me to take the car to a "radiator specialis"! I didn't even know till then that there are radiator specialists. I said its unfortunate that I have to take the car to some questionable non-authorized place when I'v come to the larges MASS in the city. He said no procedure or tools for the same have been authorized for the same by Maruti, so they would be unable to help.

Hi Racoon,
There are many so called RADIATOR SPECIALIST & you may find one near some car garage OR repair market.
I know one very goog guy here in Mumbai because I have seen him fix the most complex & fragile (read radiators of Vintage & Classic cars) radiators.
They have their own divised tools but mainly use blow gun & aluminium solder rods AND THEY ARE NOT EXPENSIVE.
However I dont see any reason for you to go for such repairs till the TEMP needle in your car is 'happy'

.

Raab Rakha.

libranof1987 · 22nd March 2012, 11:06

About the Radiator specialists that the SA mentioned, there indeed are many such. There was this tiny shop filled with radiators of all sizes near my house in B'lore.

As per my observation, what they is - rinse the radiator completely in kerosene (what it seemed like) and drain it off. They then set right all the radiator fins with a pair of tweezers. The fins are extremely delicate and they handle them with just as much care. The radiator is flushed in kerosene again.

Ask around FNGs in Pune; they might know where such guys are.

im_srini · 22nd March 2012, 11:23

Quote:

Originally Posted by Raccoon

Thats when I noticed that fins in the lower right corner were bent. The area of bent fins must be v approximately 25% of the total surface area. I recall reading in books that bent fins can be straightened by some kind of tool.

Quote:

Originally Posted by 1self

One way to 'straighten' the fins (which are not badly mutilated to begin with) would be to use a strong & sturdy hair comb, the tooth spacing of which closely matches the fin spacing of your heat exchanger. Then just go over fins. They will straighten out!

Yes, a comb can be used in a pinch & would straighten out the worst of the bent fins. If the fins are bent only slightly, the comb won't help much & finding a matching comb that is sturdy could be difficult. Radiator & A/C repair shops usually have a metal comb that they use to straighten bent fins. Here's a professional product. But, as advised by many members, if the fins aren't bent much & you've not noticed anything untoward so far, just leave it be...

vikram_d · 22nd March 2012, 11:25

My suggestion would be not to try and straighten them. Just leave them as they are. They will not cause any problems. Straightening them may only lead to other fins getting bent.

rajeev k · 22nd March 2012, 11:40

Usually radiators are designed for 10 to 15% additional capability and hence would not be a concern. Further you too noticed it only when the grill was removed and not while the car was running which means there waere no physical symptom like over heating. So could do without any repair. Leave it alone.

22nd March 2012, 02:22	#1
Raccoon Senior - BHPian Join Date: Jan 2008 Location: Poona Posts: 1,851 Thanked: 116 Times	Radiator Fins Bent - any solution? Car (Esteem) has been at the MASS for Body Shop work. When I'd been there to have a look, they had removed the front bumper and headlights and the radiator was in full view. Thats when I noticed that fins in the lower right corner were bent. The area of bent fins must be v approximately 25% of the total surface area. I should have taken pics, but it did not occur to me at that time. I recall reading in books that bent fins can be straightened by some kind of tool. Today, the car went to the Workshop, after the body shop work and I asked the SA about it. He was totally blank about the issue and could offer no solution. I persisted and told him there should be some way or some tool or "comb" for the job. I even made him call his boss and ask. Spoke to the boss myself. He didn't plead ignorance outright; rather asked me to take the car to a "radiator specialis"! I didn't even know till then that there are radiator specialists. I said its unfortunate that I have to take the car to some questionable non-authorized place when I'v come to the larges MASS in the city. He said no procedure or tools for the same have been authorized for the same by Maruti, so they would be unable to help. My questions are: 1) how good an idea would be to leave the fins as they are? They will obviously mar the cooling efficiency, but how serious would it be? The SA blankly said it should be ok to leave it as it is. 2) Does anybody know how one can get them straightened? Is there any workshop or something in Pune where I can get this done? Not sure if I'm keen on leaving it as it is as I'd not like to keep stuff thats not working optimally. Can somebody advice, please?
	() Thanks

22nd March 2012, 04:35	#2
mayankjha1806 Senior - BHPian Join Date: Jan 2011 Location: Bangalore Posts: 2,159 Thanked: 989 Times View My Garage	Re: Radiator Fins Bent - any solution? Whenever the Service engineers do some sort of work around the radiator area the fins do get touched, and because they are very fragile a slight pressure is enough for them to bend slightly. When my baleno met with an accident 3 years back at MASS they had to take the radiator out to fix it, and i also noticed the fins were bend. The function of fins is to precipitate heat and help in cooling. Now if most of the fins are alright and you have not noticed any drop in cooling effectiveness then its alright to leave them as it is, otherwise its better to show it to the radiator guys. In my case nothing was done as it was bend on about 10%-20% of area.
	() Thanks

22nd March 2012, 05:44	#3
condor Distinguished - BHPian Join Date: Jun 2006 Location: Speed-brkr City Posts: 16,238 Thanked: 16,870 Times View My Garage	Re: Radiator Fins Bent - any solution? @Racoon, like Mayank said, the fins are delicate and very often get bent. But it does not mar the cooling efficiency. Any in-efficiency in the cooling may be more because of clogging inside the radiator, and hardly due to bent fins. Unless the radiator itself is damaged, I suggest you let it be. You can also check any other car of similar age - any make any model - and you will see there are many more such cars, and running fine.
	() Thanks

22nd March 2012, 06:06	#4
nitrous Senior - BHPian Join Date: May 2004 Location: UAE/Lon/Madras Posts: 6,965 Thanked: 333 Times View My Garage	Re: Radiator Fins Bent - any solution? Watch the temperature gauge and drive. If you feel the car's overheating, then look into the issue. Don't try to mend what's not broken.
	(1) Thanks

22nd March 2012, 06:59	#5
1self BHPian Join Date: Sep 2006 Location: Pune Posts: 629 Thanked: 334 Times View My Garage	Re: Radiator Fins Bent - any solution? One way to 'straighten' the fins (which are not badly mutilated to begin with) would be to use a strong & sturdy hair comb, the tooth spacing of which closely matches the fin spacing of your heat exchanger. Then just go over fins. They will straighten out! Last edited by 1self : 22nd March 2012 at 07:00.
	(1) Thanks

22nd March 2012, 08:12	#7
mayankjha1806 Senior - BHPian Join Date: Jan 2011 Location: Bangalore Posts: 2,159 Thanked: 989 Times View My Garage	Re: Radiator Fins Bent - any solution? Although i have never tried this myself, but my guess is combs wont work. You might end up damaging it more then what it already is. @1self Have you personally tried this, or have you seen someone doing something like this? @Raccoon if you are really hell bent on getting them straightened my guess is, taking a small forceps and gently straightening each millimeter of each Finn all the way might only work. A full day affair i must say with no tangible benefits. So better leave it as it is.
	() Thanks

22nd March 2012, 08:32	#8
greenhorn BANNED Join Date: Apr 2007 Location: KL-01 Posts: 7,878 Thanked: 4,910 Times View My Garage	Re: Radiator Fins Bent - any solution? is it something like what happened here (scroll down for the pics) ? http://www.team-bhp.com/forum/techni...ler-query.html
	() Thanks

22nd March 2012, 08:32	#9
S5157 BHPian Join Date: Sep 2009 Location: Muvattupuzha, K Posts: 305 Thanked: 191 Times	Re: Radiator Fins Bent - any solution? The fins are bent on my 2010 sx4 as well. It is on lower side and behind the bumper slits. It looks like some flying debris from the road has caused it. I checked the same with the SA at MASS and he mentioned that it will not affect the performance and let it be like that.
	() Thanks

22nd March 2012, 11:06	#12
libranof1987 Team-BHP Support Join Date: Sep 2010 Location: All over! Posts: 8,175 Thanked: 20,586 Times	Re: Radiator Fins Bent - any solution? About the Radiator specialists that the SA mentioned, there indeed are many such. There was this tiny shop filled with radiators of all sizes near my house in B'lore. As per my observation, what they is - rinse the radiator completely in kerosene (what it seemed like) and drain it off. They then set right all the radiator fins with a pair of tweezers. The fins are extremely delicate and they handle them with just as much care. The radiator is flushed in kerosene again. Ask around FNGs in Pune; they might know where such guys are.
	() Thanks

22nd March 2012, 11:25	#14
vikram_d Senior - BHPian Join Date: Jul 2006 Location: Bangalore Posts: 2,422 Thanked: 1,188 Times	Re: Radiator Fins Bent - any solution? My suggestion would be not to try and straighten them. Just leave them as they are. They will not cause any problems. Straightening them may only lead to other fins getting bent.
	(1) Thanks

22nd March 2012, 11:40	#15
rajeev k Senior - BHPian Join Date: Jul 2009 Location: Emerging Metro Posts: 3,351 Thanked: 1,954 Times	Re: Radiator Fins Bent - any solution? Usually radiators are designed for 10 to 15% additional capability and hence would not be a concern. Further you too noticed it only when the grill was removed and not while the car was running which means there waere no physical symptom like over heating. So could do without any repair. Leave it alone.
	() Thanks